Page 1 of 2 12 LastLast
Results 1 to 10 of 16
  1. #1
    Moderator
    TTC5's Avatar
    Join Date
    Feb 2011
    Location
    Australia
    Posts
    8,436

    Digital pH tester from Dick Smith

    I just bought this, please tell me this will work lol i will add a link later when imhome but if u go to dicksmith.com.au and search deluxe ph tester you can find it.
    Fathers Day baby!


    Busy Mummy of 5 now working from home: www.oz.scentsy.com.au

  2. #2
    Dream User

    Join Date
    Mar 2011
    Location
    NZ
    Posts
    94
    I have that one and it seemed to do just fine. I did have to keep recalibrating it but I wanted to make sure my readings were right.
    6
    5
    1



    ??? ??? What are my twins?

    Predicted at 13wk6day scan

  3. #3
    Moderator
    TTC5's Avatar
    Join Date
    Feb 2011
    Location
    Australia
    Posts
    8,436
    Thankyou! Does the solution it comes with last long?
    Fathers Day baby!


    Busy Mummy of 5 now working from home: www.oz.scentsy.com.au

  4. #4
    Moderator
    TTC5's Avatar
    Join Date
    Feb 2011
    Location
    Australia
    Posts
    8,436
    Just a quick question I followed the instructions but did not find them very clear :S
    It says to gently stir the probe in the solution until the numbers stabilise but I could not get this to happen, unless I layed it down flat for a few seconds???
    Fathers Day baby!


    Busy Mummy of 5 now working from home: www.oz.scentsy.com.au

  5. #5
    Dream User

    Join Date
    Mar 2011
    Location
    NZ
    Posts
    94
    I found I would stir it then hold it still in the solution with the probe not touching the sides and it would stabilise.
    6
    5
    1



    ??? ??? What are my twins?

    Predicted at 13wk6day scan

  6. #6
    Moderator
    TTC5's Avatar
    Join Date
    Feb 2011
    Location
    Australia
    Posts
    8,436
    I will try that =)
    What number do you set yours to calibrate at? I hope I am doing this right...
    Fathers Day baby!


    Busy Mummy of 5 now working from home: www.oz.scentsy.com.au

  7. #7
    Moderator
    TTC5's Avatar
    Join Date
    Feb 2011
    Location
    Australia
    Posts
    8,436
    Ok I tried it again but found the numbers never settled still, they would still bounce around is this normal? Does the movement from your hands etc affect reading?

    My cm this time came at around 6.9... was hoping it would be higher =(
    Fathers Day baby!


    Busy Mummy of 5 now working from home: www.oz.scentsy.com.au

  8. #8
    Moderator
    TTC5's Avatar
    Join Date
    Feb 2011
    Location
    Australia
    Posts
    8,436
    I am due to AF any day now and cm is not very much could this affect the reading too?
    Fathers Day baby!


    Busy Mummy of 5 now working from home: www.oz.scentsy.com.au

  9. #9
    Dream User

    Join Date
    Mar 2011
    Location
    NZ
    Posts
    94
    The bottle I got had numbers to calibrate to depending on temp. I found I had to get a fair amount of CM to get a good reading. I braced my fingers on either side of the container to keep my hands steady, if it bounced back and forth a little like a point or two I din't worry about that.
    6
    5
    1



    ??? ??? What are my twins?

    Predicted at 13wk6day scan

  10. #10
    Moderator
    TTC5's Avatar
    Join Date
    Feb 2011
    Location
    Australia
    Posts
    8,436
    Ah right how do you work out your room temp or is it temP of the solution? Also how often do u calibrate it??
    Fathers Day baby!


    Busy Mummy of 5 now working from home: www.oz.scentsy.com.au

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •